Build Your Own Clone Message Board

It is currently Fri Nov 01, 2024 11:57 pm

All times are UTC - 6 hours




Post new topic Reply to topic  [ 4 posts ] 
Author Message
PostPosted: Mon Apr 29, 2024 1:27 pm 
Offline

Joined: Fri Apr 05, 2024 2:35 pm
Posts: 2
So this is a first project like this for me. My solder skills are not that great. The only major issue I ran into was I mixed up the 12k and 22k resistors and when desoldering the 22K I rendered it useless. I was unable to find the exact replacement, so I got the alternate shown on the list (see the one carbon comp 4 band beige colored). Once I got the pedal assembled, I connected a battery, put cabled ends into the intput/output jacks and clicked each button individually and the lights cycled on and off fine. Clicked both and they both came on and went out. At this point I'm thinking success but not so fast. I removed my existing boost pedal and plugged in the power supply for it (9vdc tip negative) into the silver pony 2 - plugged in the cables, clicked the foot switch button and got a blinking light. No sound when either side is switched on with blinking LEDs but with both switches off and no lights bypass works fine. I did a search on here and found a similar issue that ended up being a charge pump IC. I ordered all new ICs JIC and get the same issue. Other than the resistor issue the only thing I can think of is I melted a couple parts getting the iron too close and upon further review 2 of the IC sockets are not in the same direction as the instructions. I have attached a photo - try and look past the poor quality of my soldering and assembly - what can I do to get it working?
Image


Top
 Profile  
 
PostPosted: Tue Apr 30, 2024 10:13 am 
Offline
Moderator
User avatar

Joined: Tue Jan 02, 2007 1:24 pm
Posts: 16287
Location: Albany, NY
BigKahuna wrote:
...and upon further review 2 of the IC sockets are not in the same direction as the instructions.

The sockets have no function other than to hold the IC's in the circuit without the need for soldering and for ease of removal. The notch in one end is just there as a visual clue for which way to insert the IC, assuming that you've installed the socket per the PCB silkscreen. But the socket will do its job in either orientation.

What IS critically important is that the IC's are oriented correctly, i.e. with the notch and/or circular mark corresponding to the notch on the outline on the silkscreen. Consequently, two of your TL072's are mounted backwards in that photo--the one on the left and the one in the middle. Swap those around and see where you're at.

_________________
“My favorite programming language is SOLDER” - Bob Pease (RIP)

My Website * My Musical Gear * My DIY Pedals: Pg.1 - Pg.2


Top
 Profile  
 
PostPosted: Tue Apr 30, 2024 2:38 pm 
Offline

Joined: Fri Apr 05, 2024 2:35 pm
Posts: 2
duhvoodooman wrote:
BigKahuna wrote:
...and upon further review 2 of the IC sockets are not in the same direction as the instructions.

The sockets have no function other than to hold the IC's in the circuit without the need for soldering and for ease of removal. The notch in one end is just there as a visual clue for which way to insert the IC, assuming that you've installed the socket per the PCB silkscreen. But the socket will do its job in either orientation.

What IS critically important is that the IC's are oriented correctly, i.e. with the notch and/or circular mark corresponding to the notch on the outline on the silkscreen. Consequently, two of your TL072's are mounted backwards in that photo--the one on the left and the one in the middle. Swap those around and see where you're at.


That makes perfect sense, but I learned long ago when messing with things I have no experience at take nothing for granted. I flipped those 2 T072's around and that fixed it. Thanks so much for your help. What an awesome feeling!


Top
 Profile  
 
PostPosted: Tue Apr 30, 2024 6:01 pm 
Offline
Moderator
User avatar

Joined: Tue Jan 02, 2007 1:24 pm
Posts: 16287
Location: Albany, NY
Great! ENJOY!! :mrgreen:

_________________
“My favorite programming language is SOLDER” - Bob Pease (RIP)

My Website * My Musical Gear * My DIY Pedals: Pg.1 - Pg.2


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 4 posts ] 

All times are UTC - 6 hours


Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group